Last Updated on May five, 2019 by

RSE CCNA 2 Affiliate 1 Quiz Answers 2018 2019

  1. What is the purpose of a routing protocol?

    • It is used to build and maintain ARP tables.
    • It provides a method for segmenting and reassembling data packets.
    • It allows an administrator to devise an addressing scheme for the network.
    • Information technology allows a router to share information about known networks with other routers.
    • It provides a procedure for encoding and decoding data into bits for package forwarding.

  2. Which 2 statements describe static routes? (Choose two.)

    • They are created in interface configuration mode.
    • They require manual reconfiguration to accommodate network changes.
    • They automatically become the default gateway of the router.
    • They are identified in the routing table with the prefix Due south.
    • They are automatically updated whenever an interface is reconfigured or shutdown.

  3. Here is a link to the PT Activity.

    Open the PT Activity. Perform the tasks in the action instructions and so answer the question.

    When PC0 pings the web server, which MAC address is the source MAC address in the frame from R2 to the spider web server?

    • 0001.43EA.3E03
    • 0001.9756.6278
    • 0001.C972.4201
    • 0001.C972.4202
    • 0002.16D6.A601
      Explanation:

      In the segment between R2 and the web server, when R2 encapsulates a frame to be sent to the web server, R2 uses the MAC address of its interface that is direct connected to the segment, Fa0/1, equally the source MAC.

  4. A new junior network intern connects a laptop to an access layer switch in the wiring closet. After configuring a terminal emulation program, the intern presses the Enter key, and the S1_ATC_E2> prompt appears. What could have been done to better protect the switch?

    • Create a banner message.
    • Create a console password.
    • Utilise the enable undercover command.
    • Utilize the service password-encryption control.
      Caption:

      Configuring the console line with a countersign requires the password to be entered earlier the switch prompt tin can exist accessed. A banner is only a alert message. The enable secret command encrypts the enable password. The service countersign-encryption command protects all passwords from being seen when the show running-configuration command is used.

  5. Why are routers needed in networking?

    • to connect devices to a LAN
    • to guarantee delivery of packets
    • to provide a status on bundle delivery
    • to forrad network traffic to remote networks
    • to route information and accept acknowledgments of data delivery
      Explanation:

      One of the bones functions of a router is to connect different networks. Each interface on a router belongs to a different network. LAN devices can be continued through switches. Packet commitment, bundle commitment status, and acknowledgments are functions of the send layer.

  6. Refer to the exhibit. What is the purpose of the router port that is shown?

    RSE CCNA 2 Chapter 1 Quiz Answers 2018 2019 01

    RSE CCNA 2 Affiliate one Quiz Answers 2018 2019 01

    • to fill-in the IOS
    • to configure the router
    • to run an IOS from an alternating location
    • to connect to a port on a switch
      Explanation:

      The exhibited port is a USB port that is found on some Cisco router models. This USB port provides console access to the router, which allows access to the CLI for configuration purposes. The pale blue background backside the icon is too the standard color that is used on Cisco devices to point a panel connection.

  7. What is a gateway of concluding resort?

    • the IP address of another router
    • the IP address of the Internet provider
    • a term to describe a default gateway on a host device
    • where dropped packets are sent
      Caption:

      Even though a gateway of last resort could exist an IP address of an ISP router, this does not have to be the instance. A gateway of last resort, as seen in a Cisco routing table, is simply the IP address that is used to route packets addressed to networks not explicitly listed in the routing table. A Windows-based computer uses the term default gateway, not gateway of last resort.

  8. When a router learns that multiple paths are available to a destination network from the same routing protocol, which factor is considered by a router to choose the all-time path to forward a packet?

    • the lowest metric
    • the social club of paths on the routing table
    • the fastest bandwidth of exiting interfaces
    • the reliability value of the neighboring routers
      Explanation:

      When a router learns that multiple paths are available to a destination network from the same routing protocol, the route with the lowest metric is put into the routing tabular array to forward packets toward that network.

  9. What address and prefix length is used when configuring an IPv6 default static route?

    • ::/0
    • ::1/128
    • 0.0.0.0/0
    • FF02::1/viii
      Caption:

      The IPv6 accost and prefix for a default static road is ::/0. This represents all zeros in the address and a prefix length of zero.

  10. Which two statements correctly describe the components of a router? (Cull two.)

    • RAM permanently stores the configuration file used during the boot sequence.
    • ROM contains diagnostics executed on hardware modules.
    • NVRAM stores a backup copy of the IOS used during the boot sequence.
    • Flash memory does non lose its contents during a reboot.
    • ROM contains the most current and most consummate version of the IOS.
    • Wink contains boot system commands to place the location of the IOS.
      Explanation:

      A router contains four types of retentivity:

      • RAM – volatile memory used to store the running IOS, running configuration file, routing tabular array, ARP table, too every bit serve as a parcel buffer
      • ROM – nonvolatile memory used to hold a limited version of the IOS, bootup instructions, and basic diagnostic software
      • NVRAM – nonvolatile memory used to hold the startup configuration file
      • Flash – nonvolatile memory used to hold the IOS and other organization files

  11. Which feature on a Cisco router permits the forwarding of traffic for which there is no specific route?

    • next-hop
    • gateway of last resort
    • road source
    • outgoing interface
      Explanation:

      A default static route is used as a gateway of concluding resort to frontward unknown destination traffic to a side by side hop/exit interface. The next-hop or exit interface is the destination to send traffic to on a network later the traffic is matched in a router. The route source is the location a route was learned from.

  12. The output of the show ip route command contains the following entry:

    S x.two.0.0 [1/0] via 172.16.2.two.

    What value is indicated past the 1 in the [ane/0] portion of the output?

    • metric
    • number of hops
    • authoritative distance
    • interface ID through which the network tin can be reached
      Explanation:

      In the routing table entry, South 10.2.0.0 [ane/0] via 172.xvi.2.2, the numbers within the subclass indicate the administrative distance and metric respectively.

  13. What code is used in the routing table to identify routes learned through EIGRP?

    • C
    • D
    • L
    • O
    • S
      Explanation:

      Each route in a routing table has a code that identifies how the route was learned by the router. The lawmaking letter D is used to identify routes that are learned through EIGRP.

  14. Which two statements depict characteristics of load balancing? (Choose two.)

    • Load balancing occurs when a router sends the same package to different destination networks.
    • Load balancing occurs when the same number of packets are sent over static and dynamic routes.
    • Load balancing allows a router to forward packets over multiple paths to the same destination network.
    • Diff cost load balancing is supported by EIGRP.
    • If multiple paths with different metrics to a destinations exist, the router cannot support load balancing.

  15. During the procedure of encapsulation, how does the PC decide if the packet is destined for a host on a remote network?

    • by checking the ARP cache for the destination host MAC address
    • by querying the DNS server for the information of the destination host
    • by sending a circulate to the local LAN segment to see if in that location is any response
    • past performing the AND operation on the destination IP address and its ain subnet mask
      Explanation:

      When a PC needs to encapsulate a frame to ship a data bundle, it first performs an AND functioning with its ain IP and subnet mask, which yields the network accost. And then it performs some other AND performance using the destination IP and the same subnet mask. By comparing the ii AND operations results, the PC knows if the destination is on the local LAN or on a remote network.